quik-coat® MD 5
tna quik-coat® MD 5 is the ultimate mandrel dispensing unit that applies a variety of free flowing ingredients consistently onto the top of products passing underneath. The tna quik-coat® MD 5 is custom configured for width and ingredients.
Belt Dryer
The Rosenqvists Belt Dryer works on air with low temperature and high humidity that ensure even drying results of each strip. The Belt Dryer uses the counter-air-flow principle where the airflow covers the full width of the belts.
CCW-RV Open Frame Weigher
Ishida’s latest IP69K waterproof weigher is now fully open for cleaning.
Series 1750 Flush Grid Belt
The new Intralox® Series 1750 Flush Grid belt takes abrasion resistance to a new level. It is a superior solution for use in the harsh conditions wet (potato) receiving lines.
Octal-R Conveyors & Elevators
Wyma's Octal-R Conveyors & Elevators transport produce efficiently to different parts of your line. Produce is fed on to the conveyor or elevator and is transported in the direction of belt motion.
FastBack® Left Right Center (LRC) Diverting Weigher Infeed Solution
The FastBack Left Right Center (LRC) is a compact double multihead weigher feed solution designed to provide a precise, consistent product stream to Ishida's patented back-to-back 218 twin weigher.
Sponsored Content
Sponsored Content
Sponsored Content
Sponsored Content
Multi Zone French Fry Fryer
The Rosenqvists Multi-Zone frying system uses a minimum of oil resulting in high-quality french fry with a longer shelf life. They combine the latest technologies using computer simulation programs and build efficient and reliable process equipment.
Heracles Flavour Liquids and Solids system
Heracles is a robust and high capacity equipment, designed for high productions or for products that are difficult to aromatize.
Aspire storage system
The aspire system for open boxes is also a direct ventilation system. The air in the room is conditioned and then sucked through the boxes. All kinds of standard open boxes can be used for this system.
Drop Limit Box Tipper
The Drop limit box tipper is a box tipper where the drop is limited, which leads to less damage to the product. The tilting of the box is done in three steps: The cubic box is put into the machine, after which the crate is clamped against a cover plate.
Creep Feed Hopper
Wyma's Creep Feed Hopper receives, stores, and conveys dirty produce that has a high level of dirt and clods. Wyma's Creep Feed Hopper is a dry hopper. It receives wet or dry produce with a high level of dirt and clods, allows for fast unloading and changeover time without starving your line of produce, and provides produce buffering.
Vibrating Piece Remover
Wyma's Vibrating Piece Remover removes unwanted produce pieces and debris early in your processing line and prior to packaging. Produce and debris are fed ontothe bed, which is made up of corrugated channels.
Sponsored Content
You May Also Like
Straight Cut 6x6mm French Fries
Living upto the expectations that encompass this segment, they bring in a new touch to this variety of fries. IBF premium high solid fries not only guarantee crispiness and good holding times
conti-pro® FF 3
Florigo conti-pro® FF 3 is a French fries frying system designed with a process intended to boost the efficiency of your production line.
Flo-Dry Dryer
The Flo-Dry system is a natural gas-fired, Single or Triple pass oven-dryer designed to evaporate moisture from extruded snacks and other products. These are typically receiving the product at the inlet at around 9-10% (exit extruder) and outputting the product at 1-2%.
clear-cut® SWM 3
Florigo clear-cut® SWM 3 is an efficient water cutting system that is able to handle a variety of cutting styles for potatoes – all while eliminating product damage.
Flo-Cool® ROCS
Flo-Cool® ROCS The latest Flo-Cool® system pumps oil through a HX system–to rapidly cool frying oil for storage in a day/over nigh tank–resulting in faster clean-down/change overtimes.
Hydrocutter
SFW Hydrocutter is a piece of industrial food processing equipment that uses high-pressure water jets to cut and slice food products. The hydrocutter consists of a pump, a high-pressure water system, and a cutting head.
